If you own a shed you’ll need to know how to felt a shed roof. Over time the sun, rain and wind will cause your roof felt to break down and start letting water in, which if left, can cause the wood to rot and your shed’s contents to get damp and eventually mouldy.
Replacing the roof felt is a quick and relatively simple DIY job that won’t cost too much or take too long. Combine a new look leak-free roof with thebest exterior wood paintand you’ll have a watertight shed that will last.
Here we reveal the tools and techniques you’ll need to make felting a shed roof happen.
How to felt a shed roof: A step-by step guide
To get the job done you are going to need roof felt like thisGreen Polyester Shed Roofing Felt from Amazon, nails like theseDiall Galvanised Clout nails from B&Q, a hammer, a sharp Stanley knife, tape measure and a ladder.
1. Prepare your felt
Pick a dry day and before you start, unroll your roof felt on your patio or lawn to help flatten it out. Now is a good time to measure up and cut the lengths you’ll need for the job (you will probably need three). Measure the roof panel and add around 150-200mm to the overall length.
现在测量屋顶和减少直接的感觉edge – a spare scrap of wood will do – and a Stanley knife. Repeat for each length. Add a weight on each end to help flatten.
2. Remove the old felt
If replacing the old felt on a roof the first step is to remove it. You’ll need a step ladder to access the roof. First remove the fascia boards (also known as barge boards). These are the timber strips that hold down the felt at each end of the roof.
Start by pulling up any loose roof felt. If needed, use a knife to make a cut to get started. For more stubborn areas use a wide paint scraper/putty knife like theDEKTON Professional Scraper from Amazonto get under the felt.
Once all the felt has been removed use a claw hammer to get rid of all the remaining nails.
3. Secure the felt
现在卷起第一条,在屋顶上and unroll. Move into position and make sure that it overhangs both ends by around 100mm. Get a nail – start in one corner on the edge nearest the top of the roof apex – and fix the felt into place.
Pull the other end to straighten and pull the felt tight so that it lies flat. Fix into place with a nail and then place a nail around every 15cm. Repeat this on the other side. Finally, lay the last strip over the apex of the roof, pull to tighten and straighten and nail into place, making sure it overlaps on top of the felt that has already been laid on either side.
4. Fix edges and finish
Make a vertical slit in the overhanging part of the roof felt on the apex of the roof. This will allow you to fold it neatly and overlap. Nail in the fascia board to secure the overlap in place. Trim any excess with a knife. Finally, fold the felt under the edges and nail into place.
Can you felt over old felt on a shed?
Yes you can but it's not recommended. If you are replacing your shed roof felt it is typically because the old felt has broken down and is letting water in, not giving the protection it should. Removing the old felt will also allow you to see if there is any damage to the roof that needs fixing or replacing.
How much felt will I need for my shed?
This will obviously depend on the size of your shed, so before you start you will need to measure up. If you have a traditional apex shed you will have two roof panels, simply measure the length and width of one panel. As an example an 8 x 6 foot shed will typically have a roof panel that is approx 8 foot long and just under 4 feet wide – or approximately 2.4m x 1.1m.
Shed roof felt comes in metric measurements and is typically one metre wide and 10m in length, so covers 10m2. With overlap you will need approximately 8m2 (or one roll) to cover the roof of an 8 x 6 feet shed. Or in simpler terms you will need three strips – 2.5m x 1m – to cover the roof.
